The roller shutter door and the remote control can only be used normally if they are paired. Otherwise, Jinan remote control roller shutter door remote control can not start the roller shutter door. In order to let you use it smoothly, let's show you how to pair the roller shutter door remote control.

一◕✘✘₪、捲簾門遙控器怎麼配對

1◕✘✘₪、 How to pair the remote control of rolling shutter door

1◕✘✘₪、在對碼之前╃·↟₪▩，需要先確定你所購買的捲簾門遙控器和原先捲簾門遙控器的晶片以及相關的配件型號保持一致╃·↟₪▩，需要購買和原來遙控器相匹配的╃·↟₪▩，這樣才可以進行對碼╃•。

1. Before checking the code, you need to make sure that the chip and relevant accessory models of the roller shutter door remote controller you purchased are consistent with those of the original roller shutter door remote controller. You need to buy the one that matches the original remote controller, so that you can check the code.

2◕✘✘₪、將購買的遙控器上面的兩個按鍵同時按住╃·↟₪▩，按下之後等遙控器上面的指示燈閃爍╃·↟₪▩，就可以將手鬆開了╃•。

2. Press and hold the two buttons on the purchased remote control at the same time. After pressing, wait for the indicator light on the remote control to flash, and then you can release your hand.

3◕✘✘₪、將原來的遙控器和現在正在使用的遙控器拿在一起╃·↟₪▩，且同時按一下這兩個遙控器上面的開門鍵╃·↟₪▩，等指示燈閃爍之後╃·↟₪▩，就表示複製成功了╃·↟₪▩，等開門鍵複製成功╃·↟₪▩，還可以複製其他的按鍵╃·↟₪▩，複製的方法是一樣的╃·↟₪▩，複製好了之後就可以對碼成功了╃•。

3. Take the original remote control and the remote control currently in use together, and press the open key on the two remote controls at the same time. When the indicator light flashes, it means that the copy is successful. When the open key is copied successfully, you can also copy other keys. The copy method is the same. After the copy is completed, you can successfully match the code.

注意事項·✘│✘：

matters needing attention:

1◕✘✘₪、使用捲簾門遙控器時╃·↟₪▩，需要確定使用的是哪種型號的遙控器╃·↟₪▩，要知道晶片的型號╃•。使用之前需要清碼╃·↟₪▩，可以看到遙控器上面有兩個按鍵╃·↟₪▩，指示燈閃一次之後我們就可以再按一下╃·↟₪▩，之後就能夠清除成功╃•。

1. When using the remote control for the roller shutter door, you need to determine which type of remote control is used and the chip model. You need to clear the code before using it. You can see that there are two buttons on the remote control. After the indicator light flashes once, we can press it again, and then we can clear it successfully.

2◕✘✘₪、使用遙控器要進行對碼╃·↟₪▩，比如遙控器和對碼的遙控器放在一起╃·↟₪▩，同時按下任意的一個鍵╃·↟₪▩，這時就會看到指示燈會閃一下╃·↟₪▩，就表明複製成功了╃·↟₪▩，前後可能只有1-2秒鐘╃·↟₪▩，再按照相同的辦法把其他的三個按鍵都要對上╃•。

2. Use the remote control to check the code. For example, put the remote control and the remote control of the code together, and press any key at the same time. At this time, you will see that the indicator will flash once, indicating that the copy is successful. It may only take 1-2 seconds before and after, and then use the same method to check the other three keys.

以上就是關於捲簾門遙控器怎麼配對╃·↟₪▩，捲簾門遙控器不好使了怎麼辦的全部內容╃·↟₪▩，希望可以幫助大家瞭解捲簾門遙控器╃·↟₪▩，更多相關捲簾門的內容就來我們網站http://www.whb-zj.com諮詢瞭解吧✘₪•▩！

The above is all about how to match the remote control of the roller shutter door and what to do if the remote control of the roller shutter door is not working properly. I hope it can help you understand the remote control of the roller shutter door. More information about the roller shutter door can be found on our website http://www.whb-zj.com Ask about it!